Professional help for personal care

28th September 2021

     

Font size: - +

When a leading global manufacturer of personal care equipment needed a production solution that combined cost reduction with quality improvement, they came to OMRON, a trusted partner they had worked with many times. For this particular line, they needed something that would help with a very specific task, right at the end of production.

Meeting the challenge


The task at hand? Tightening the final screw into a personal grooming device- simple enough you might think. But the intricate process is something that takes great care, accuracy, and attention to detail, and involves differing form factors and models, with differing placements of screws per model, which is why it’s generally finalised by hand.

Professional solutions

“The customer approached us to see if it was possible to bring a collaborative robot in to help the operator,” Barry Oorbeek, Key Account Manager Industry Solutions at OMRON Benelux explains. The solution design phase involved a thorough audit of needs: “Omron Safety Services Europe (OSSE) first conducted a machine risk analysis, then a Sistema calculation, to define the requirement specifications for the system integrator,” says Barry. “From here we were able to prioritise and plan for the commissioning phase of the project.

Selection & setup

“In the setup phase, we used the intuitive plug & play software to establish virtual ‘safety fences’ prior to installation. This set clear boundaries around the cobot, to limit its range of movement to its specific area of operation.” This ensured complete predictability, so that the operator had a confident understanding of where the cobot would be, and what it would be doing, at all times.

Safety first

For the customer, the key criterion was of course safety, since the cobot would be working in close proximity with a human operator. From the various options suited for the task, they chose the OMRON TM5-700, a unit built for quick start-ups, rapid changeovers and of course, inherent safety, as Barry explains. “From the points highlighted in the machine risk analysis, OSSE then conducted extensive force- and pressure-testing, going through each potential risk point, establishing the maximum permissible pressure, and confirming that the cobot was able to instantly and accurately sense the results of its actions.”

This testing covered all the delicate movements involved in screwing the unit cover into place, so the cobot detected when the screw was firmly in place, without overtightening. And since everything is programmable, once the actions are performed perfectly once, they are fixed in memory, for right first time—every time—action.

Rapid start-up, intuitive operation

An intuitive human-machine interface within the machine controller gives full overview and control of the cobot, which is designed for ease of use. Operators need only 5 minutes’ instruction before starting to work with the system, which was engineered to keep pace with the speed of the manual production line.

Ideal human/cobot mix

“This system goes a long way to solve a very common problem in production lines,” says Barry Oorbeek. “Repetitive tasks done by hand can suffer from quality variation over time. With this solution, the customer has the ideal combination—the flexibility of an operator to handle the high diversity of components, with the accuracy and sensitivity of the OMRON cobot to perform the repetitive screw-fastening process.”

So why not fully automate?

The customer in this case already has a large installed base of OMRON robots in place, with some automated screwdriving in automated lines. But this particular workstation is used for a variety of form factors and end-products, so it was decided to bring a cobot on board, since there may be multiple changes per day of the product that’s being finalised. “OMRON cobots are designed to be supremely flexible, both in the way they are simple to program, and in the way that they can be used. Here for instance, the customer can achieve single-minute exchange of dies (SMED), moving from one product type to another extremely quickly.”

The end result?

“A delighted customer,” Barry concludes proudly. “Their process quality has improved, and they have an integrated solution that was quickly verified and validated.” This OMRON customer is currently investigating the use of OMRON cobots in other areas of its production facilities.
 

Edited by Creamer Media Reporter

Comments

The functionality you are trying to access is only available to subscribers.

If you are already a subscriber, you can Login Here.

If you are not a subscriber, you can subscribe now, by selecting one of the below options.

For more information or assistance, please contact us at subscriptions@creamermedia.co.za.

Option 1 (equivalent of R125 a month):

Receive a weekly copy of Creamer Media's Engineering News & Mining Weekly magazine
(print copy for those in South Africa and e-magazine for those outside of South Africa)
Receive daily email newsletters
Access to full search results
Access archive of magazine back copies
Access to Projects in Progress
Access to ONE Research Report of your choice in PDF format

Option 2 (equivalent of R375 a month):

All benefits from Option 1
PLUS
Access to Creamer Media's Research Channel Africa for ALL Research Reports, in PDF format, on various industrial and mining sectors including Electricity; Water; Energy Transition; Hydrogen; Roads, Rail and Ports; Coal; Gold; Platinum; Battery Metals; etc.

Already a subscriber?

Forgotten your password?

MAGAZINE & ONLINE

SUBSCRIBE

RESEARCH CHANNEL AFRICA

SUBSCRIBE

CORPORATE PACKAGES

CLICK FOR A QUOTATION