https://www.engineeringnews.co.za

Four ways to optimise pump performance

16th March 2017

     

Font size: - +

This article has been supplied as a media statement and is not written by Creamer Media. It may be available only for a limited time on this website.

SKF  (0.07 MB)

Pumps are the foot soldiers of the process industry, but their quiet dedication means they are often ignored.

Ignoring the pumps is a big risk, because when these components break down – or run below optimum efficiency – the whole process suffers. Manufacturing and process companies are under huge cost pressures at the moment, making it vital to maximise assets and maintain uptime. There are ways to optimise their performance in four different ways.

The right bearing
Bearings in centrifugal pumps support hydraulic loads imposed on the impeller, the mass of the impeller and shaft, as well as loads due to couplings and drive systems. They also keep the shaft axial and radial deflections within acceptable limits for the impeller and shaft seal.

The bearings often will face high axial loads, marginal lubrication, and high operating temperatures and vibration, all while the bearings attempt to minimise friction — which, if uncontrolled, can result in power loss, excessive heat generation, increased noise or wear, and early bearing failure. So, first and foremost, evaluate bearings (types, designs and arrangements) in the context of their anticipated operating environment. Suitable bearings are available to satisfy even the most difficult conditions faced by centrifugal pumps.

Proper lubrication
Improper lubrication accounts for more than 30% of bearing failures. Good lubricants prevent metal-to-metal contact and undesired friction. The common methods for the effective lubrication of pump bearings include: grease, oil bath, oil ring, and oil mist and air-oil. 

Oil mist generates the least amount of friction (allowing rotational speed to be based on the bearing design instead of lubrication limitations) and creates a positive pressure within the bearing housing (fending off invasive contaminants). Regardless of lubrication method, always specify lubricant according to the demands on vertical shafts and resistance to solids, pressure, temperatures, loads and chemical attack.

Sealing the system
Bearing seals in centrifugal pumps handle four crucial tasks. They retain lubricants or liquids, exclude contaminants, separate fluids and confine pressure. The choice of seal for centrifugal pump bearings depends on the unique demands and operating conditions of the application. Keep in mind, though, that the bearing and sealing arrangement represent an integrated system. Dynamic radial seals generally are the best choice for centrifugal pumps. These seals create the barrier between surfaces in relative motion. Seal selection ultimately must be based on a thorough review of application parameters and environmental factors.

Particularly in pump applications, for example, seals will be exposed to relatively constant pressure differentials — making pressure seals (in which the seal cavity is pressurised) the preferred choice. Seals usually provide a much shorter life than the components they protect so don’t fall into the common habit of scheduling seal replacement only at intervals dictated by requirements of other components such as bearings.

Monitoring pump health
Regular measurement and analysis of key physical parameters such as vibration and temperature can detect pump system problems before they occur. Basic instruments can assess and report on vibration, temperature and other parameters. More advanced tools include online surveillance systems and software that can deliver real-time data. Many problems will manifest as vibration, which is widely considered the best operating parameter to judge pump-train condition.

Vibration can detect problems such as imbalance, misalignment, bearing oil-film instabilities, rolling bearing degradation, mechanical looseness, structural resonance and a soft foundation. Vibration measurements are quick and fairly non-intrusive because pump equipment remain undisturbed.

Edited by Creamer Media Reporter

Comments

Showroom

Schauenburg SmartMine IoT
Schauenburg SmartMine IoT

SmartMine IoT has been developed with the mining industry in mind, to provides our customers with powerful business intelligence and data modelling...

VISIT SHOWROOM 
Actom image
Actom

Your one-stop global energy-solution partner

VISIT SHOWROOM 

Latest Multimedia

sponsored by

Option 1 (equivalent of R125 a month):

Receive a weekly copy of Creamer Media's Engineering News & Mining Weekly magazine
(print copy for those in South Africa and e-magazine for those outside of South Africa)
Receive daily email newsletters
Access to full search results
Access archive of magazine back copies
Access to Projects in Progress
Access to ONE Research Report of your choice in PDF format

Option 2 (equivalent of R375 a month):

All benefits from Option 1
PLUS
Access to Creamer Media's Research Channel Africa for ALL Research Reports, in PDF format, on various industrial and mining sectors including Electricity; Water; Energy Transition; Hydrogen; Roads, Rail and Ports; Coal; Gold; Platinum; Battery Metals; etc.

Already a subscriber?

Forgotten your password?

MAGAZINE & ONLINE

SUBSCRIBE

RESEARCH CHANNEL AFRICA

SUBSCRIBE

CORPORATE PACKAGES

CLICK FOR A QUOTATION







sq:0.069 0.124s - 158pq - 2rq
Subscribe Now